ThermoX® LED housing

Article no: 9320-21
E no.: 920849539
EAN: 4013456545717

for rigid and pivoting LED luminaires
circumferential airtight sealing lip
Swivel trough for alignment of the luminaire

Depth

95 mm

installation from front, cut hole Ø

86 mm

Cable entries

max. installation depth for the LED luminaires

85 mm

max. lamp output

10 Watt

max. ceiling exit (DA) Ø

81 mm

Dispatch

Add to the project list

Download product data sheet (PDF)

Show additional downloads

Installation housing ThermoX® LED

ThermoX® LED installation housing for the airtight installation of rigid and pivoting LED built-in luminaires in different ceiling constructions. The housing protects the surrounding material (vapour barrier foil, insulation etc.) against the high operating temperatures and the LED luminairesthemselves from contamination, and creates an airtight separation. In combination with the thermal separation between luminaire and operating device, in this way a maximum operating lifetime is obtained.

For installation in insulated hollow ceilings
Retrofitting from underneath
Toolless installation of the housing
Guarantees airtight installation
Rear surface structure ensures optimal heat management
Permanent and secure retention of the luminaire in the housing

Examples of use

ThermoX® LED installation housings can be installed in seamless sub-ceiling constructions made of plywood...

...MdF board,...

...slab ceilings with single battens with overlying insulation...

...and installing plasterboard.

Temperature profiles ThermoX® LED (room temperature 25ºC)

ThermoX® LED 9320-10 LED 6.6 W

ThermoX® LED 9320-11 LED 9 W

ThermoX® LED 9320-20 LED 8 W

ThermoX® LED 9320-21 LED 10 W

Air-tight installation and fire-preventive protection

The ThermoX® LED housing protects the surrounding material against the extremely high temperatures that may occur during the operation of LED lamps. The housing must be installed without any surrounding insulating material coating. This protective measure can be taken both for new constructions and for retrofitting. The LED housing allows for air-tight installation because it does not destroy the vapour barrier foil that contributes to the air-tight building shell. Because of their air tightness, LED housings are also suitable for use in all suspended ceiling systems where uncontrolled air exchange is to be avoided (e.g. climate or cooling ceilings) and dustproof installation needs to be achieved (e.g. prevention of dust particles due to material removal).

Installation

Make cut opening (e.g. cutter PROFI, Art. No. 1081-20).

To enlarging existing installation openings from Ø 68 mm to Ø 74 mm using centering insert (Art. No. 1083-99).

Installation of the operating device (driver).

Feed connector from below through the entry of the LED installation housing.

Connection of the plug-in contacts. Feed the sealing element round the cable and insert into the opening.

Installation of the ThermoX® LED housing in the installation opening.

Inserting the spotlight into the housing.

Rear surface structure minimises pressure on the vapour barrier and ensures optimal heat dissipation.

Technical processing instructions/standards

use only certified (EN 60598) luminaires which are suitable for direct installation on normally flammable materials

Processing instructions

Guaranteed air tightness even when the fixing springs are expanded.

Expanding pockets ensure secure fit for the built-in luminaire.

Swivel pocket permits targeted alignment of the built-in luminaire

For ceiling-flush installation of ThermoX® LED (DA 86), use bi-metal cutter Ø 86 mm (Art. No. 1084-86).

Installation notes

Art. No. 9320-10 ThermoX® LED, Ø 74 x 75 mm

Art. No. 9320-11 ThermoX® LED, Ø 74 x 95 mm

Art. No. 9320-20 ThermoX® LED, Ø 86 x 75 mm

Art. No. 9320-10 ThermoX® LED, Ø 86 x 95 mm

Air-tightness certificate

Guaranteed airtight housing for the energy-efficient electrical installation of luminaires. The appropriate certificate can be obtained from us or downloaded from our website.